1 cde cornell dubilier ? 1605 e. rodney french blvd. ? new bedford, ma 02744 ? phone: (508)996-8561 ? fax: (508)996-3830 type pfcs, 3-phase ac power factor correction capacitors type pfcs 3-phase series capacitors are designed for power factor correction in automatic pfc controllers. each pfcs capacitor is made with three self-healing metallized polypropylene windings, connected in delta, enclosed in a cylindrical aluminum case and flled with an environmentally friendly fuid. specifcations capacitance tolerance 0 to +10% rated frequency (f r ) 50 hz and 60 hz rated ac voltages (v r ) 240 vac, 480 vac, 600 vac operating temperature range C40 oc to +55 oc kvar range 0.5 kvar to 30.2 kvar maximum permissible voltage (vmax) 110% of rated rms voltage 120% of rated peak voltage (1.2 x 2x vrms) internal connection delta (?) maximum permissible current (imax) 135% of nominal rms current based on rated kvar and rated voltage - (up to 150% of l r including combined efects of harmonics, over voltages and capacitances, tolerance) life 60,000 h w/94% survival rate international standards meets ieee18, standard (ansi/ieee standard 18) fit (failure in time) 300 x 10 9 component h maximum short circuit current 10 ka (according to ul 810) mechanical and electrical safety pressure interrupter (pi) disengages all 3 phases in the event of capacitor end of life or overload discharge resistor time 60 seconds 50 v for 600 v or less; over 600 v 5 minutes rohs compliant dimensions figure 1 figure 2 highlights - for 3-phase ac power factor correction - delta connected - discharge resistors included - ul810 approved internal pressure interrupter construction details case material extruded aluminum with steel or aluminum cover encapsulation environmentally safe dielectric fuid terminal material tin plated copper, brass or steel max torque 88.5 in-lbs. max torque 88.5 in-lbs.
2 pfc s t 480 c 6 s 779 t type base type voltage case material kvar tolerance can height phases (vac) (%) (inches) pfc s = std. s = 2 round 24 = 240 c = aluminum case full kvar value s = 0/+10% expressed as 3 digit t = 3-phase t = 2? round 48 = 480 w/steel cover including decimals rounded and displayed v = 3 round 60 = 600 m12 stud @ 60 hz and without decimal point x = 3.5 round d = aluminum case w/aluminum cover m12 stud cde cornell dubilier ? 1605 e. rodney french blvd. ? new bedford, ma 02744 ? phone: (508)996-8561 ? fax: (508)996-3830 ratings part numbering system type pfcs, 3-phase ac power factor correction capacitors cde catalog number 60hz 50hz capacitance (f) case output i r output i r diameter (in) height (in) style kvar (a) kvar (a) 240vac pfcss24c0.5s572t 0.5 1.2 0.4 1.0 3 x 7.7 2.0 5.72 fig. 1 pfcss24c1s572t 1 2.4 0.8 2.0 3 x 15.4 2.0 5.72 pfcss24c1.5s572t 1.5 3.6 1.3 3.0 3 x 23.0 2.0 5.72 pfcss24c2s572t 2 4.8 1.7 4.0 3 x 30.7 2.0 5.72 pfcss24c2.5s572t 2.5 6.0 2.1 5.0 3 x 38.4 2.0 5.72 PFCST24C3S572T 3 7.2 2.5 6.0 3 x 46.1 2.5 5.72 pfcst24c4s572t 4 9.6 3.3 8.0 3 x 61.4 2.5 5.72 pfcst24c5s778t 5 12.0 4.2 10.0 3 x 76.8 2.5 7.78 pfcsv24d6s635t 6 14.4 5.0 12.0 3 x 92.1 3.0 6.35 fig. 2 pfcsx24d6.3s635t 6.3 15.2 5.3 12.6 3 x 96.7 3.5 6.35 pfcsx24d7.5s635t 7.5 18.0 6.3 15.0 3 x 115.1 3.5 6.35 pfcsv24d8.3s842t 8.3 20.0 6.9 16.6 3 x 127.4 3.0 8.42 pfcsx24d10s842t 10 24.1 8.3 20.0 3 x 153.5 3.5 8.42 pfcsx24d12.5s842t 12.5 30.1 10.4 25.1 3 x 191.9 3.5 8.42 pfcsx24d15s108t 15 36.1 12.5 30.1 3 x 230.3 3.5 10.78 pfcsx24d16.7s108t 16.7 40.2 13.9 33.5 3 x 256.4 3.5 10.78 pfcsx24d17.5s108t 17.5 42.1 14.6 35.1 3 x 268.6 3.5 10.78 pfcsx24d20s137t 20 48.1 16.7 40.1 3 x 307.0 3.5 13.73 480vac pfcss48c0.5s572t 0.5 0.6 0.4 0.5 3 x 1.9 2.0 5.72 fig. 1 pfcss48c1s572t 1 1.2 0.8 1.0 3 x 3.8 2.0 5.72 pfcss48c1.5s572t 1.5 1.8 1.3 1.5 3 x 5.8 2.0 5.72 pfcss48c2s572t 2 2.4 1.7 2.0 3 x 7.7 2.0 5.72 pfcss48c2.5s572t 2.5 3.0 2.1 2.5 3 x 9.6 2.0 5.72 pfcss48c3s572t 3 3.6 2.5 3.0 3 x 11.5 2.0 5.72 note: other ratings, sizes and performance specifcations are available. contact us.
3 cde cornell dubilier ? 1605 e. rodney french blvd. ? new bedford, ma 02744 ? phone: (508)996-8561 ? fax: (508)996-3830 type pfcs, 3-phase ac power factor correction capacitors cde catalog number 60hz 50hz capacitance (f) case output i r output i r diameter (in) height (in) style kvar (a) kvar (a) 480vac pfcss48c4s572t 4 4.8 3.3 4.0 3 x 15.4 2.0 5.72 fig. 1 pfcst48c5s572t 5 6.0 4.2 5.0 3 x 19.2 2.5 5.72 pfcst48c6s572t 6 7.2 5.0 6.0 3 x 23.0 2.5 5.72 pfcst48c7.5s778t 7.5 9.0 6.3 7.5 3 x 28.8 2.5 7.78 pfcsv48d8.3s635t 8.3 10.0 6.9 8.3 3 x 31.9 3.0 6.35 fig. 2 pfcsv48d9s635t 9 10.8 7.5 9.0 3 x 34.5 3.0 6.35 pfcsx48d10s635t 10 12.0 8.3 10.0 3 x 38.4 3.5 6.35 pfcsv48d12.5s842t 12.5 15.0 10.4 12.5 3 x 48.0 3.0 8.42 pfcsv48d15s108t 15 18.0 12.5 15.0 3 x 57.6 3.0 10.78 pfcsv48d16.7s108t 16.7 20.1 13.9 16.7 3 x 64.1 3.0 10.78 pfcsv48d18s108t 18 21.7 15.0 18.0 3 x 69.1 3.0 10.78 pfcsv48d20s108t 20 24.1 16.7 20.0 3 x 76.8 3.0 10.78 pfcsx48d25s108t 25 30.1 20.8 25.1 3 x 95.9 3.5 10.78 pfcsx48d30s137t 30 36.1 25.0 30.1 3 x 115.1 3.5 13.73 600vac pfcss60c1s572t 1 1.0 0.8 0.8 3 x 2.5 2.0 5.72 fig. 1 pfcss60c1.5s572t 1.5 1.4 1.3 1.2 3 x 3.7 2.0 5.72 pfcss60c2s572t 2 1.9 1.7 1.6 3 x 4.9 2.0 5.72 pfcss60c2.5s572t 2.5 2.4 2.1 2.0 3 x 6.1 2.0 5.72 pfcss60c3s572t 3 2.9 2.5 2.4 3 x 7.4 2.0 5.72 pfcss60c4s572t 4 3.8 3.3 3.2 3 x 9.8 2.0 5.72 pfcst60c5s572t 5 4.8 4.2 4.0 3 x 12.3 2.5 5.72 pfcst60c6s572t 6 5.8 5.0 4.8 3 x 14.7 2.5 5.72 pfcst60c6.1s572t 6.1 5.9 5.1 4.9 3 x 15.0 2.5 5.72 pfcst60c6.3s572t 6.3 6.1 5.3 5.1 3 x 15.5 2.5 5.72 pfcst60c6.9s778t 6.9 6.6 5.8 5.5 3 x 16.9 2.5 7.78 pfcsv60d7.5s635t 7.5 7.2 6.3 6.0 3 x 18.4 3.0 6.35 fig. 2 pfcsv60d8.1s635t 8.1 7.8 6.8 6.5 3 x 19.9 3.0 6.35 pfcsv60d8.3s635t 8.3 8.0 6.9 6.7 3 x 20.4 3.0 6.35 pfcsx60d10s635t 10 9.6 8.3 8.0 3 x 24.6 3.5 6.35 pfcsv60d12.2s842t 12.2 11.7 10.2 9.8 3 x 30.0 3.0 8.42 pfcsv60d12.5s842t 12.5 12.0 10.4 10.0 3 x 30.7 3.0 8.42 pfcsv60d13.8s842t 13.8 13.3 11.5 11.1 3 x 33.9 3.0 8.42 pfcsv60d14.6s108t 14.6 14.0 12.2 11.7 3 x 35.9 3.0 10.78 pfcsv60d15s108t 15 14.4 12.5 12.0 3 x 36.8 3.0 10.78 pfcsv60d16.7s108t 16.7 16.1 13.9 13.4 3 x 41.0 3.0 10.78 pfcsv60d17.5s108t 17.5 16.8 14.6 14.0 3 x 43.0 3.0 10.78 pfcsv60d20s108t 20 19.2 16.7 16.0 3 x 49.1 3.0 10.78 pfcsv60d22.5s108t 22.5 21.7 18.8 18.0 3 x 55.3 3.0 10.78 pfcsx60d25s108t 25 24.1 20.8 20.0 3 x 61.4 3.5 10.78 pfcsx60d30.2s137t 30.2 29.1 25.2 24.2 3 x 74.2 3.5 13.73
4 type pfcs, 3-phase ac power factor correction capacitors notice and disclaimer: all product drawings, descriptions, specifcations, statements, information and data (collectively, the information) in this datasheet or other publication are subject to change. the cus - tomer is responsible for checking, confrming and verifying the extent to which the information contained in this datasheet or other publication is applicable to an order at the time the order is placed. all informa - tion given herein is believed to be accurate and reliable, but it is presented without any guarantee, warranty, representation or responsibility of any kind, expressed or implied. statements of suitability for certain appli - cations are based on the knowledge that the cornell dubilier company providing such statements (cornell dubilier) has of operating conditions that such cornell dubilier company regards as typical for such ap - plications, but are not intended to constitute any guarantee, warranty or representation regarding any such matter C and cornell dubilier specifcally and expressly disclaims any guarantee, warranty or representation concerning the suitability for a specifc customer application, use, storage, transportation, or operating environment. the information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. any technical advice inferred from this in - formation or otherwise provided by cornell dubilier with reference to the use of any cornell dubilier prod - ucts is given gratis (unless otherwise specifed by cornell dubilier), and cornell dubilier assumes no obliga - tion or liability for the advice given or results obtained. although cornell dubilier strives to apply the most stringent quality and safety standards regarding the design and manufacturing of its products, in light of the current state of the art, isolated component failures may still occur. accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies or other appropriate protective measures) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated in such warnings, cautions and notes, or that other safety measures may not be required.
|
